Nursing Cover Tutorial

nursing cover tutorial
With all of my babies, my nursing cover was one of my most-used and most appreciated items. They make the perfect gift for a new mom, and can be whipped up in no time!

Description:
A stylish and practical nursing cover. The dimensions are slightly larger than most nursing covers, which gives added coverage and less chance of someone getting an uninvited sneak peek!

You will need:
1.25 yd fabric (home décor weight works best)
16” boning – in fabric casing – can be found in local fabric shops or online here (affiliate link)
2 D-rings – 1.25”-1.5” – these 1.5″ D-rings (affiliate link) are my favorite to use

Fabric pieces to cut:
·
one rectangle 28”x40” for main body
· one strip 4.25”x10” for neck strap
· one strip 4.25”x26” for neck strap

Directions:
1. First we will complete the neck straps… Take 4.25”x10” strip of fabric and fold in half lengthwise right sides together. Stitch ¼” from edge along raw edges, forming a tube. Repeat with longer strip, but sew a curve towards the inner fold when you are reaching the last few inches of the strip. Trim seam allowance around curve close to the stitching line.

2. Turn each piece right side out and press flat with the seam going down the center of the strap. Topstitch ¼” from each edge on both straps.

3. Place shorter strap through D-rings, matching up raw edges. Stitch as close to the D-rings as possible, encasing them between the two layers of the strap.

4. On to the main body of the nursing cover… With your main body rectangle of fabric, fold and press upper edge (if your fabric has a definite pattern, ensure you know which side should be at the top!) ½” toward wrong side of fabric. This should be your 40” long edge. Fold and press again ½”.

5. Open up the folded edge and center the boning along the raw edge (I used black boning for demonstration purposes), with the boning curving away from you (sounds more confusing that it is… now’s a good time to take a look at the picture below). There should be 12” of the pressed edge on either side of the boning. Pin boning in place.

6. Stitch along upper edge of boning casing (depending on your boning, your stitching may need to be nearer the top edge). Stitch at either end of boning casing, ensuring that boning is completely covered by the casing. If needed, first trim 1/8” off of each boning end (plastic only, not the casing) to allow casing to completely cover the boning. This will assure OCD people like me that the boning will not move or poke through the casing or your fabric.

7. Allow the upper edge of fabric to fold over again the way it was pressed. With the right sides facing toward you, take each neck strap and tuck under folded edge, centering each strap at the edge of each end of boning. Pin in place. Stitch along lower edge of fold.

8. Press neck straps upward, away from the main body. Stitch along upper edge of main body, backstitching at edges of straps, securing neck straps in their final and upward position.

9. Fold and press lower edge of nursing cover ½”, fold another ½” and press again as was done with the upper edge. Stitch close to folded edge. Repeat with raw side edges.

Note: If you would like to add an interior pocket that can also be used as a burp cloth, simply cut a right-angle triangle piece of terry towel or chenille the size you would like your pocket to be, allowing enough fabric for a hem on the top edge. Hem the top edge, sandwich the raw edges of the triangle between one lower side and the bottom pressed edges before they have been stitched, and stitch the pocket right into place while you sew the bottom and side edge. I have personally never needed a pocket because it seems I always have a big diaper bag with me anyway and a separate burp cloth, but it’s a simple step to add if you think you might like one!

10. Thread the long strap through the front of the D-rings and back out again through one on the underside.

11. You are done, great job!

Give it away as a gift or keep it for yourself!

Diaper Bag Tutorial

Diaper Bag Tutorial
Want to make a hip diaper bag that your friends will envy and you will love for both its style and its practicality? This diaper bag tutorial will make a bag that’s large enough to hold all your baby’s needs with room left over for your must-haves too! Features include being fully lined and spacious interior pockets that you can customize. Interior pockets can be made using lining fabric or exterior fabric for contrast.

 

If you’re looking for a full diaper bag pattern complete with full sized printable pieces, check out our Airdrie Bag Pattern or Lola Bea Diaper Bag Pattern!

 

Diaper Bag Tutorial

You will need:
(affiliate links below)
Exterior Fabric – 1 yd (1.25 yd if making interior pockets using exterior fabric for contrast) – home décor weight fabric works best

Lining Fabric – 1.25 yd (1 yd if making interior pockets using exterior fabric for contrast) – home decor weight fabric works best
Lightweight Woven Fusible Interfacing – 1.5 yd
¼” elastic – 1 yd
½” double fold bias tape – 1.5 yd
Magnetic snap
Your favorite sewing music (I recommend John Mayer, Ben Harper, and Jack Johnson)

Pieces to cut (see diagram if you want to ignore my writing):

Exterior fabric:
Cut 2: 20×18” rectangle for main body of bag, with 4×4” square cut out of bottom corners *double check direction of pattern in fabric before cutting is correct*
Cut 2: 3×26” strips for straps
Cut 1: 3×6” rectangle for magnetic snap closure tab, angle corners on one side if desired
If making interior pockets out of exterior fabric for contrast: Cut 2: 8×26” rectangles

Lining fabric:Cut 2: 20×18” rectangle for main body of bag, with 4×4” square cut out of bottom corners
Cut 2: 3×26” strips for straps
Cut 1: 3×6” rectangle for magnetic snap closure tab, angle corners on one side if desired
If making interior pockets out of lining fabric (do not cut out of lining fabric AND exterior fabric): Cut 2: 8×26” rectangles

Interfacing:Cut 2: 20×18” rectangle for main body of bag, with 4×4” square cut out of bottom corners (along 18” side)
Cut 2: 3×26” strips for straps
Cut 2: 3×6” rectangle for magnetic snap closure tab, angle corners on one side if desired

Double fold bias tape:
Cut 2: 26” length

Elastic:
Cut 2: 14” lengths

*All seam allowances are 1/2” unless otherwise noted.*

Directions:

1. Iron interfacing to corresponding exterior fabric pieces on the wrong side of fabric including the main body and straps. Iron interfacing to magnetic snap closure tab pieces of lining and exterior on wrong side of fabric.

2. Right sides together, sew the 2 main body pieces of exterior fabric together at bottom seam and press open. Sew side seams and press open. At the opening where you cut the 4” squares, match and pin the bottom seams to the side seams and sew using a ¼” seam allowance. Press seams towards top of bag.
3. Mark placement of magnetic snap by measuring 4.5” from top center of bag and attach bottom half of magnetic snap using manufacture’s instructions.

*Turn fabric right side out and place somewhere that you can see it when you are getting frustrated later on to keep you motivated (that’s why I always do the exterior first)!

4. Attach top half of magnetic snap to closure tab piece of lining. Right sides together, pin to exterior closure tab and sew ¼” seam, angling at corners if desired. Turn right side out and topstitch 1/4″ from edge.
5. Right sides together, pin and sew exterior fabric strap to lining fabric strap. Sew ¼” seam down each side, leaving ends open. Turn right side out, press, and topstitch along each side close to edge. Repeat for other strap.
6. Sandwich bias tape over top edge of interior pocket fabric and sew close to edge, forming a casing for the elastic.

7. Press 4-5 evenly spaced pintucks into bottom edge of interior pocket, until width of interior pocket is 20”. Stitch along lower edge to secure pintucks. Turn lower edge under ¼” to wrong side and press, turn another ¼” and press.
8. Thread elastic through backside of casing and backstitch at both ends to secure. Pin wrong side of pocket to right side of main body lining 5” from the top of the lining, matching up side edges, and topstitch two rows along lower pintucked edge. Stitch pocket to lining at sides.

9. Stitch vertical lines through lining and interior pocket to form individual pockets that fit your needs.
10. Repeat steps 6-9 using 2nd interior pocket and 2nd piece of main body lining fabric.

11. Complete lining of bag using step 2 above.

12. Right sides together, place exterior fabric main body inside lining main body, pinning at side seams. Sandwich closure tab on back center of bag (opposite of side that bottom half of magnetic snap was attached), ensuring that the exterior fabric right sides are facing each other. Sandwich outer edge of straps 3” in from each side seam, again ensuring that the exterior fabric right sides are facing each other.
13. Leaving a 4-5” opening, stitch along upper edge of bag, through exterior fabric, lining fabric, straps, and closure tab. Turn bag right side out, trim seam to reduce bulkiness if needed, and press. Hand stitch opening of bag closed and top stitch 1/2″ from edge. Top stitch another row 1/4″ from top edge.
14. Take a good long look at your bag because you are finished this diaper bag tutorial, and can start filling it up!

Diaper Bag Tutorial